MAKSTTON Vehicle Fitment Guide

Chery Arrizo 8 Pro Wheel Fitment Guide

By Zhenjie Duan · September 2026

Based on a 2025 Chery Arrizo 8 Pro measured by MAKSTTON, this guide covers the 5×108 bolt pattern, center-bore and wheel-bolt specifications, the factory 18-inch wheel and tire package, measured fender clearance and the recommended wheel specifications. Chassis dimensions are shared across Arrizo 8 versions, so the measurements can be used as a reference for other trims.

View Recommended Fitment
Chery Arrizo 8 Pro measured by MAKSTTON

Chery Arrizo 8 Pro Fitment at a Glance

Fitment Item MAKSTTON Reference
Bolt Pattern (PCD) 5×108
Published Center Bore 65.1mm
Measured Wheel Center Bore 65.106mm
Measured Hub Diameter 65.05mm
Recommended Center Bore 65.1mm
Factory Wheel 18×7.5J ET46
Factory Tire 225/45R18
Minimum Wheel Load Rating 556kg per wheel

Vehicle and Load Reference

The vehicle measured by MAKSTTON is a 2025 Chery Arrizo 8 Pro. Its maximum permissible gross weight is 1,853kg, the figure used for the wheel-load calculation in this guide. Chassis dimensions are shared across Arrizo 8 versions, so the measurements below can be used as a reference for other trims.

View image
Chery Arrizo 8 Pro vehicle identification plate showing a 1,853kg maximum permissible gross weight

Arrizo 8 Pro vehicle identification plate photographed by MAKSTTON

Factory Wheel and Tire Specifications

MAKSTTON recorded one factory wheel-and-tire configuration on the measured vehicle. Front and rear use the same wheel and tire size.

Position Wheel Offset Tire
Front 18×7.5J ET46 225/45R18
Rear 18×7.5J ET46 225/45R18
View images
Factory Chery Arrizo 8 Pro 18×7.5J ET46 wheel with 225/45R18 tire

Factory 18-inch wheel photographed by MAKSTTON

Chery Arrizo 8 Pro factory wheel with its decorative cover fitted

Factory wheel with cover fitted photographed by MAKSTTON

Chery Arrizo 8 Pro factory wheel with the decorative cover removed, showing the hub face

Factory wheel hub face photographed by MAKSTTON

Bolt Pattern and Center Bore

Specification MAKSTTON Reference
Bolt Pattern (PCD) 5×108
Published Center Bore 65.1mm
Measured Wheel Center Bore 65.106mm
Measured Hub Diameter 65.05mm
MAKSTTON Recommended Center Bore 65.1mm
View image
Micrometer measuring the center bore of a Chery Arrizo 8 Pro wheel

Wheel center bore measured with a micrometer by MAKSTTON

The measured values are the recorded readings from that vehicle. Small differences may occur between vehicles, measuring positions and measuring conditions.

Chery Arrizo 8 Pro Wheel Bolt Specifications

Fastener Item Specification
Fastener Type Wheel bolts
Thread Size M14×1.5
Thread Length 30mm
Seat Type R13 ball seat
Strength Grade Not marked
Hex Size 17mm
View images
Steel rule measuring the threaded length of a Chery Arrizo 8 Pro wheel bolt

Threaded length measured by MAKSTTON

Thread pitch gauge checking the M14×1.5 thread of a Chery Arrizo 8 Pro wheel bolt

Thread pitch checked with a thread gauge by MAKSTTON

Caliper measuring the major diameter of a Chery Arrizo 8 Pro wheel bolt thread

Thread major diameter measured by MAKSTTON

Caliper measuring the overall length of a Chery Arrizo 8 Pro wheel bolt

Overall bolt length measured by MAKSTTON

Valve Stem and TPMS

The measured Chery Arrizo 8 Pro is fitted with rubber valve stems. A rubber stem cannot be transferred to a new set of wheels, so an alloy valve stem must be added when the wheels are changed. Where a vehicle is already fitted with alloy valve stems, those can be reused directly with the tire-pressure monitoring sensors. The valve-stem mounting position on this vehicle is parallel.

View images
Chery Arrizo 8 Pro rubber valve stem on the factory wheel

Rubber valve stem photographed by MAKSTTON

Chery Arrizo 8 Pro valve-stem mounting position with the parallel structure

Parallel valve-stem mounting position photographed by MAKSTTON

Wheel Load Requirement

The factory Chery Arrizo 8 Pro wheel is marked with a rated load of 600kg. Using the conventional load factor of 1.2 against the recorded maximum permissible gross weight of 1,853kg:

1,853 ÷ 4 × 1.2 = 555.9kg

MAKSTTON therefore recommends a minimum rated load of at least 556kg per wheel for this application.

Measured Wheel-to-Fender Clearance

Baseline: factory 18×7.5J ET46 package with 225/45R18 tires at factory suspension height, measured from the fender lip to the outer wheel rim.

Measurement Front Left Front Right Rear Left Rear Right
Fender lip to wheel rim ≈23mm ≈23mm ≈28mm ≈28mm
Fender lip to tire sidewall ≈18mm ≈19mm ≈26mm ≈26mm
Suspension height ≈80mm ≈80mm ≈58mm ≈60mm
Fender lip thickness ≈10mm ≈3mm

Front inner tire sidewall to suspension: ≈2.5 fingers.

Use this guide as a baseline, not the final answer. Measurements from your own vehicle are always more valuable. Read our Flush Fitment Guide, measure your car, and calculate the fitment that matches the stance you want.

MAKSTTON Custom Fitment Recommendation

Based on the factory suspension height.

5mm Wheel-Rim Inset from the Fender

18×8.0J — Factory Tire

Position Wheel Size Offset Tire
Front 18×8.0J ET35 225/45R18
Rear 18×8.0J ET26 225/45R18

18×8.5J — Wider Tire

Position Wheel Size Offset Tire
Front 18×8.5J ET42 245/40R18
Rear 18×8.5J ET33 245/40R18

19×8.5J — 19-Inch Upgrade

Position Wheel Size Offset Tire
Front 19×8.5J ET42 245/35R19
Rear 19×8.5J ET33 245/35R19

Wheel width: the factory 18×7.5J wheel can be upgraded to 8.0J with the factory 225/45R18 tire, or to 8.5J with a 245/40R18 (18-inch) or 245/35R19 (19-inch) tire.

Fender clearance may vary slightly between vehicles due to production tolerances. Use these figures as a reference only.

In-Stock MAKSTTON Wheel Options

These ready-to-ship MAKSTTON wheel styles — flow-formed FF designs and low-pressure-cast MST designs — are stocked in 5×108 fitments, so a Chery Arrizo 8 Pro set can often ship without waiting for a custom build. For this car MAKSTTON supplies these ready-to-ship styles rather than custom forged builds. Confirm the offset and center bore against the exact vehicle before ordering.

Availability, offset and center bore are confirmed on each product page. Contact MAKSTTON to confirm the exact 5×108 specification for this vehicle before ordering.

Real-World Chery Arrizo 8 Fitment Cases

Case 01 — MAKSTTON FF FK08

Chery Arrizo 8 fitted with MAKSTTON FF FK08 18×8J ET40 wheels on 235/45R18 tires
View More Fitment Photos & Installation Details →
Item Front Rear
Wheel Model MAKSTTON FF FK08
Wheel 18×8J ET40 18×8J ET40
Tire 235/45R18 235/45R18
Suspension Factory

Case 02 — MAKSTTON FF MR7

Chery Arrizo 8 fitted with MAKSTTON FF MR7 18×8J ET35 wheels on 225/45R18 tires
View More Fitment Photos & Installation Details →
Item Front Rear
Wheel Model MAKSTTON FF MR7
Wheel 18×8J ET35 18×8J ET35
Tire 225/45R18 225/45R18
Suspension Factory

MAKSTTON Vehicle Measurement Record

This original MAKSTTON workshop data-collection sheet is included for reference. For mainstream vehicles, MAKSTTON may review and summarize measurements from multiple vehicle records rather than rely on a single sheet.

Original MAKSTTON Chery Arrizo 8 Pro wheel, hub, bolt and chassis measurement data sheet

Original vehicle measurement record completed by MAKSTTON

Chery Arrizo 8 Pro Wheel Fitment FAQ

What are the Chery Arrizo 8 Pro bolt pattern and center bore?

The bolt pattern is 5×108. The published center-bore specification is 65.1mm, which is also the size MAKSTTON machines for this application. The inspected vehicle recorded a wheel center-bore reading of 65.106mm and a hub diameter of 65.05mm.

What wheel fitment does MAKSTTON recommend for the Chery Arrizo 8 Pro?

MAKSTTON's fitment reference for this car covers three options at roughly 5mm rim inset from the fender. With the factory tire: 18×8.0J, ET35 front / ET26 rear on 225/45R18. With a wider tire: 18×8.5J, ET42 front / ET33 rear on 245/40R18. As a 19-inch upgrade: 19×8.5J, ET42 front / ET33 rear on 245/35R19. See the final recommendation table for the full specification.

What wheel bolts does the Chery Arrizo 8 Pro use?

The Chery Arrizo 8 Pro uses M14×1.5 wheel bolts with an R13 ball seat, a 30mm thread length and a 17mm hex. The factory bolts do not carry a marked strength grade.

What minimum wheel load rating should be specified?

The factory wheel is marked 600kg. Using a load factor of 1.2 and the recorded maximum permissible gross weight of 1,853kg, MAKSTTON uses at least 556kg per wheel as the reference for a custom wheel on this vehicle.

Can I fit a wider tire on the Chery Arrizo 8 Pro?

A 245-section tire is a documented upgrade on an 8.5J wheel — 245/40R18 for 18-inch wheels or 245/35R19 for 19-inch wheels. The front inner tire-to-suspension clearance measured about 2.5 fingers on the factory package, so wider tires and aggressive offsets should be verified with a test fit on the actual car.

Zhenjie Duan, Technical Department, MAKSTTON

Zhenjie Duan | Technical Department

Renbing Xiong, Technical Department, MAKSTTON

Technical data: Renbing Xiong | Technical Department

If you have any questions, find an error in this guide or have additional verified fitment data, please contact MAKSTTON at info@makstton.com.