MAKSTTON Vehicle Fitment Guide

ZEEKR 9X Wheel Fitment Guide

By Binghua Yang · September 2026

The ZEEKR 9X is a large luxury SUV with a maximum permitted mass of up to 3,660kg. Based on vehicle measurements collected by MAKSTTON, this guide covers the ZEEKR 9X bolt pattern, center bore, wheel-bolt specification, load-rating target, factory 22-inch wheels, fender clearance and recommended offsets for aftermarket forged wheels.

View Recommended Fitment

ZEEKR 9X Wheel Fitment at a Glance

Fitment Item	MAKSTTON Reference
Bolt Pattern (PCD)	5×108
Published Center Bore	63.4mm
Measured Hub Pilot Diameter	Front 63.32mm / Rear 63.33mm
MAKSTTON Recommended Custom Wheel Center Bore	63.30mm
Factory Wheel	22×9.5J ET37.5 or ET44.5
Factory Tire	285/45R22
Factory Wheel Fasteners	M14×1.5 wheel bolts
Gross Vehicle Weight Rating	3,660kg
Minimum Recommended Wheel Load Rating	1,190kg per wheel

ZEEKR 9X Verified Vehicle Weight

Version	GVWR
Ultra	3,545kg
Hyper	3,660kg

Wheel load calculations in this guide use the higher GVWR of 3,660kg.

Bolt Pattern and Center Bore

Specification	MAKSTTON Reference
Bolt Pattern (PCD)	5×108
Published Center Bore	63.4mm
Measured Hub Pilot Diameter	Front 63.32mm / Rear 63.33mm
MAKSTTON Recommended Custom Wheel Center Bore	63.30mm

Vehicle measurement data collected by MAKSTTON

The published ZEEKR 9X center-bore specification is 63.4mm. The original MAKSTTON workshop sheet records hub-pilot readings of 63.32mm at the front and 63.33mm at the rear on the inspected vehicle, while MAKSTTON uses a fixed 63.30mm custom-wheel production specification.

ZEEKR 9X Wheel Bolt and Lug Nut Specifications

Fastener Item	Specification
Fastener Type	Wheel bolts
Thread Size	M14×1.5
Thread Length	34mm
Seat Type	60° conical seat
Strength Grade	10.9
Hex Size	19mm

Recommended Wheel Load Rating

The factory wheels inspected by MAKSTTON did not show a visible load-rating marking. Because the ZEEKR 9X is a heavy SUV, MAKSTTON calculates its recommended target from the 3,660kg maximum permitted mass using a safety factor of 1.3:

3,660kg ÷ 4 × 1.3 = 1,189.5kg

MAKSTTON recommended minimum: 1,190kg per wheel

Factory 22-Inch Wheel and Tire Specifications

MAKSTTON measured two factory 22-inch wheel configurations for the ZEEKR 9X. Both use the same wheel width and tire size, with different offsets.

Factory Configuration	Front Wheel	Rear Wheel	Tire
Configuration 01	22×9.5J ET37.5	22×9.5J ET37.5	285/45R22
Configuration 02	22×9.5J ET44.5	22×9.5J ET44.5	285/45R22

Measured Factory Fender Clearance

Baseline: factory 22×9.5J ET37.5 package at factory suspension height, measured from the fender lip to the outer wheel rim.

Measurement	Front Left	Front Right	Rear Left	Rear Right
Fender lip to wheel rim	≈12mm	≈15mm	≈25mm	≈28mm

Use this guide as a baseline, not the final answer. Measurements from your own vehicle are always more valuable. Read our Flush Fitment Guide, measure your car, and calculate the fitment that matches the stance you want.

MAKSTTON Custom Fitment Recommendation

Based on the factory suspension height.

Primary Recommendation — 22×9.5J

Position	Wheel Size	Offset	Tire
Front	22×9.5J	ET35	285/45R22
Rear	22×9.5J	ET25	285/45R22

Optional Wider Wheel — 22×10J

Position	Wheel Size	Offset	Tire
Front	22×10J	ET41	285/45R22
Rear	22×10J	ET31	285/45R22

Fender clearance may vary slightly between vehicles due to production tolerances. Use these figures as a reference only.

Recommended MAKSTTON Wheel Designs

These six made-to-order forged wheel designs can be custom-manufactured for the ZEEKR 9X. Wheel diameter, width, offset, bolt pattern, center bore, load rating and finish are specified for the vehicle and order. The wheel and tire specifications are consolidated in the final section.

Real-World Fitment 01: ZEEKR 9X

ZEEKR 9X real-world fitment 01 on 22-inch Makstton FG BO03 silver forged wheels

View More Fitment Photos & Installation Details

This ZEEKR 9X owner selected a wheel position approximately 5mm farther outward at both axles than the standard MAKSTTON recommendation.

Item	Front	Rear
Wheel Model	MAKSTTON FG BO03
Wheel	22×9.5J ET30	22×9.5J ET20
Tire	285/45R22	285/45R22
Center Bore	63.30mm
Wheel Load Rating	1,190kg	1,190kg

MAKSTTON Vehicle Measurement Record

This original MAKSTTON workshop data-collection sheet is included for reference. For mainstream vehicles, MAKSTTON may review and summarize measurements from multiple vehicle records rather than rely on a single sheet.

Original MAKSTTON ZEEKR 9X wheel, hub, brake, fastener and chassis measurement data sheet

Original vehicle measurement record completed by MAKSTTON

ZEEKR 9X Wheel Fitment FAQ

What is the ZEEKR 9X bolt pattern and center bore?

The ZEEKR 9X uses a 5×108 bolt pattern with a 63.4mm published center bore. MAKSTTON's original workshop record shows measured hub-pilot readings of 63.32mm at the front and 63.33mm at the rear, while MAKSTTON machines its custom wheels to a fixed 63.30mm for this application.

What wheel and tire sizes does the ZEEKR 9X use from the factory?

The measured ZEEKR 9X runs 22×9.5J wheels with 285/45R22 tires, the same size front and rear. MAKSTTON recorded two factory offset variants: ET37.5 and ET44.5.

What offset (ET) does the ZEEKR 9X use?

The measured ZEEKR 9X factory wheels use ET37.5 or ET44.5, depending on the variant. MAKSTTON recommends moving to ET35 front and ET25 rear on a 22×9.5J wheel, or ET41 front and ET31 rear on the wider 22×10J option, which produces a wider track without pushing the wheel outside the arch. See the final recommendation table for the exact figures.

What wheel fitment does MAKSTTON recommend for the ZEEKR 9X?

MAKSTTON recommends 22×9.5J ET35 front and ET25 rear with 285/45R22 tires for the best balance of comfort and wheel-edge protection. A wider 22×10J ET41 front and ET31 rear option is available for a more aggressive position. See the final recommendation table for the exact specifications.

What wheel load rating does the ZEEKR 9X need?

Using a maximum permitted mass of 3,660kg and a 1.3 safety factor, MAKSTTON recommends a minimum load rating of 1,190kg per wheel. Load capacity should never be traded for a lower weight or a more aggressive appearance.

What wheel bolts does the ZEEKR 9X use?

The ZEEKR 9X uses M14×1.5 wheel bolts with a 34mm thread length, a 60° conical seat, strength grade 10.9 and a 19mm hex. Confirm the seat type and thread engagement against the new wheel before installation.

Binghua Yang | Product Development Manager

Technical data: Renbing Xiong | Technical Department

If you have any questions, find an error in this guide or have additional verified fitment data, please contact MAKSTTON at info@makstton.com.