ZEEKR 7X Wheel Fitment Guide
This guide is based on real-world measurement data from a 2025 ZEEKR 7X. The test vehicle was fitted with 20×9.0J ET43.5 OE wheels, 265/45R20 tires, a 5×108 bolt pattern, and a recommended custom center bore of 63.3 mm.
This guide covers wheel installation clearance, brake calipers and hub height, wheel fasteners, valve stems, wheel load ratings, and tire fitment. It also provides suggested forged-wheel modification parameters based on measured data, together with a complete vehicle data collection record.
ZEEKR 7X Fitment at a Glance
| Item | Data |
|---|---|
| Bolt Pattern (PCD) | 5×108 |
| Thread Specification | M14×1.5 |
| OE Nominal CB | 63.4 mm |
| OE Wheel Size | 20×9.0J ET43.5 |
| OE Tire Size | 265/45R20 |
| GVWR | 2,800 kg |
| Minimum Wheel Load Rating | ≥ 840 kg per wheel |
View vehicle body plate image
OE Wheel and Tire Specifications
| Position | OE Wheel Size | OE Tire Size |
|---|---|---|
| Front | 20×9.0J ET43.5 | 265/45R20 |
| Rear | 20×9.0J ET43.5 | 265/45R20 |
View OE wheel and tire photos
Bolt Pattern and Center Bore
ZEEKR 7X uses a 5×108 bolt pattern. The OE nominal CB is 63.4 mm; the measured wheel CB is 63.318 mm and the measured hub diameter is 63.3 mm. The recommended custom CB is 63.3 mm.
| Item | Data |
|---|---|
| Bolt Pattern (PCD) | 5×108 |
| OE Nominal CB | 63.4 mm |
| Wheel CB (Measured) | 63.318 mm |
| Measured Hub Diameter | 63.3 mm |
| Recommended Custom CB | 63.3 mm |
View center bore and hub measurement photos
Wheel Fastener Specifications
The fastener type for the vehicle recorded in this data-collection session is Wheel bolt, with thread specification M14×1.5, thread length 34 mm, seat type 60°, strength class 10.9, socket size 19 mm. The new wheel's seat type, thread engagement, and socket clearance must match the OE structure; tighten to the vehicle manufacturer's specified torque.
| Item | Data |
|---|---|
| Fastener type | Wheel bolt |
| Thread specification | M14×1.5 |
| Thread length | 34 mm |
| Seat type | 60° |
| Strength class | 10.9 |
| Socket size | 19 mm |
View wheel fastener measurement photos
Valve Stem and TPMS
The measured vehicle uses rubber valve stems. Before changing wheels, confirm whether the vehicle is equipped with a TPMS and verify the sensor type, mounting location, and compatibility with the wheel valve hole.
View valve stem and TPMS photos
Wheel Load Requirement
The vehicle's body plate states a maximum permissible gross mass of 2,800 kg.
| Calculation | Calculation Process | Recommended Rated Load per Wheel |
|---|---|---|
| Minimum required load | 2,800 kg ÷ 4 × 1.2 = 840 kg | ≥ 840 kg |
| Forged wheel requirement | 2,800 kg ÷ 4 × 1.3 = 910 kg | ≥ 910 kg |
Verify the maximum permissible gross mass on the vehicle identification plate. This value may differ between configurations of the same model, so calculate using the actual vehicle's plate data. The results above are for preliminary wheel-selection reference only.
Measured Wheel-to-Fender Clearance
Clearance data was measured with the 20-inch wheel and is expressed in millimeters. Assembly tolerances vary between the left and right sides. Actual clearance may change after a tire-brand change, suspension-height adjustment, or wheel alignment.
| Measurement | Front left | Front right | Rear left | Rear right |
|---|---|---|---|---|
| Fender to wheel edge | 16 mm | 13 mm | 14 mm | 10 mm |
| Fender to tire sidewall | 12 mm | 10 mm | 11 mm | 7 mm |
| Suspension height | 72 mm | 73 mm | 69 mm | 74 mm |
| Fender thickness | 19 mm | 17 mm |
This guide is a starting point, not the final answer. Measuring your own vehicle is more valuable. Read our Flush Fitment Guide, Measure Your Vehicle, and Calculate a Fitment Setup That Matches Your Target Stance.
View fender clearance measurement photos
MAKSTTON Custom Data Recommendation
| Setup | Tire Size | Front Wheel | Rear Wheel | Fitment State |
|---|---|---|---|---|
| 19-inch | 255/50R19 | 19×8.5J ET32 | 19×8.5J ET32 | Rim lip inset — front 7-10 mm, rear 4-8 mm. |
| 20-inch | 265/45R20 | 20×9.0J ET35 | 20×9.0J ET35 | Rim lip inset — front 4-7 mm, rear 1-5 mm. |
| 21-inch | 265/40R21 | 21×9.0J ET35 | 21×9.0J ET35 | Rim lip inset — front 4-7 mm, rear 1-5 mm. |
MAKSTTON Production Data Recommendation
| Setup | Tire Size | Front Wheel | Rear Wheel | Fitment State |
|---|---|---|---|---|
| 20-inch | 265/45R20 | 20×9.0J ET35 | 20×9.0J ET35 | Rim lip inset — front 4-7 mm, rear 1-5 mm. |
| 21-inch | 265/40R21 | 21×9.0J ET35 | 21×9.0J ET35 | Rim lip inset — front 4-7 mm, rear 1-5 mm. |
Recommended MAKSTTON Wheel Designs
Production Wheel Designs
Custom Forged Wheel Designs
Real-World Fitment Cases
Case 01 — MAKSTTON FF FK07T
| Item | Front | Rear |
|---|---|---|
| Model | MAKSTTON FF FK07T | |
| Wheel | 20×9.0J ET35 | 20×9.0J ET35 |
| Tire | 265/45R20 | 265/45R20 |
Case 02 — MAKSTTON FF FK08
| Item | Front | Rear |
|---|---|---|
| Model | MAKSTTON FF FK08 | |
| Wheel | 21×9.0J ET35 | 21×9.0J ET35 |
| Tire | 265/40R21 | 265/40R21 |
MAKSTTON Vehicle Measurement Record
The measurement record compiles wheel size, tire specification, fender clearance, suspension clearance, center bore, and fastening hardware data for future wheel-fitment checks. For mainstream vehicles, MAKSTTON may combine measurements from multiple vehicles rather than relying on a single sheet.
Frequently Asked Questions
Q:What are the bolt pattern and center bore of the ZEEKR 7X?
A:The bolt pattern (PCD) is 5×108. The OE nominal center bore is 63.4 mm. The measured wheel center bore is 63.318 mm. The recommended custom center bore is 63.3 mm.
Q:What are the OE wheel and tire specifications for the ZEEKR 7X?
A:The OE wheels are 20×9.0J, ET43.5, with 265/45R20 at both axles.
Q:What wheel sizes and offsets does MAKSTTON recommend for the ZEEKR 7X?
A:MAKSTTON recommends 19-inch: wheels 19×8.5J ET32, tires 255/50R19. 20-inch: wheels 20×9.0J ET35, tires 265/45R20. 21-inch: wheels 21×9.0J ET35, tires 265/40R21.
Q:What wheel load rating does the ZEEKR 7X require?
A:The maximum permissible gross mass is 2,800 kg. Under the current calculation rules, a conventional aftermarket wheel should be rated at no less than 840 kg per wheel, and a forged wheel at no less than 910 kg per wheel. Verify the actual gross mass on the vehicle identification plate; it may differ between configurations of the same model.
Q:What wheel bolts or nuts are used on the ZEEKR 7X?
A:This vehicle uses the following wheel-fastener specifications: fastener type: Wheel bolt; thread specification: M14×1.5; thread length: 34 mm; seat type: 60°; strength class: 10.9; socket size: 19 mm.
Q:How should wheel installation clearance be verified when upgrading the brakes on the ZEEKR 7X?
A:Before installing an aftermarket brake caliper, request the complete caliper and mounting-bracket engineering drawings from the caliper manufacturer. MAKSTTON provides measurement drawings for the OE braking system that can help verify the custom bracket dimensions and installation position. Final fitment must still be confirmed against the caliper shape, the wheel's internal structure, and actual installation clearance.
If you have questions, find an error, or have verified supplementary fitment data, contact MAKSTTON: info@makstton.com.