Makstton Vehicle Fitment Guide

LYNK & CO 08 Wheel Fitment Guide

By Binghua Yang · September 2026

The LYNK & CO 08 uses a 5×108 bolt pattern and a 63.4mm published center bore; MAKSTTON machines its custom wheels to 63.3mm for this application. The factory fitment is 19×7.5J ET46 with 235/55R19 tires on 2WD models and 21×8.5J ET46 with 255/40R21 tires on AWD models.

This guide covers 19-inch and 21-inch wheel and tire fitment for both drivetrains: the measured factory fender clearance, the recommended 19×8.5J front ET29 / rear ET39 or 19×8J front ET22 / rear ET32 and 21×9J front ET39 / rear ET43 or 21×8.5J front ET33 / rear ET37 setups, the MAKSTTON production specifications and five documented installations.

Minimum wheel load is 739kg per wheel for the 2WD and 788kg per wheel for the AWD. Confirm load rating, brake clearance and dynamic clearance on the actual vehicle before ordering.

View Recommended Fitment
LYNK & CO 08 fitted with Makstton FG FK08 forged wheels, side-profile installation view

LYNK & CO 08 Fitment at a Glance

Fitment Item MAKSTTON Reference
Bolt Pattern (PCD) 5×108
Published Center Bore 63.4mm
MAKSTTON Recommended Custom Wheel Center Bore 63.3mm
Factory Wheel 19×7.5J ET46 (2WD) | 21×8.5J ET46 (AWD)
Factory Tire 235/55R19 (2WD) | 255/40R21 (AWD)
Factory Wheel Fasteners M14×1.5 wheel bolts
Gross Vehicle Weight Rating 2,463kg (2WD) / 2,625kg (AWD)
Minimum Recommended Wheel Load Rating 739kg (2WD) / 788kg (AWD) per wheel

Factory Wheel and Tire Specifications

MAKSTTON recorded two factory wheel-and-tire configurations on the measured vehicle: one for 2WD models and one for AWD models. Each runs the same wheel and tire size front and rear.

Factory Setup Wheel Tire
2WD 19×7.5J ET46 235/55R19
AWD 21×8.5J ET46 255/40R21

These values were recorded from the documented vehicle. Factory specifications may vary slightly between versions.

Bolt Pattern and Center Bore

Specification MAKSTTON Reference
Bolt Pattern (PCD) 5×108
Published Center Bore 63.4mm
MAKSTTON Recommended Custom Wheel Center Bore 63.3mm

The 2WD and AWD versions share the same bolt pattern and center bore, so a wheel that locates on one drivetrain also locates on the other. The published center bore is 63.4mm, while MAKSTTON machines its custom wheels to 63.3mm for this application.

LYNK & CO 08 Wheel Bolt and Lug Nut Specifications

Fastener Item Specification
Fastener Type Wheel bolts
Thread Size M14×1.5
Thread Length 34mm
Overall Length 61mm
Seat Type 60° conical seat
Hex Size 19mm

Confirm the fastener seat type, thread engagement and tightening torque on the actual vehicle before the final installation.

Recommended Wheel Load Rating

The LYNK & CO 08 has a gross vehicle weight rating of 2,463kg (2WD) and 2,625kg (AWD), and the factory wheel carries no marked load rating. MAKSTTON therefore derives the target from each version's maximum permitted mass using a safety factor of 1.2:

2,463kg ÷ 4 × 1.2 = 739kg per wheel (2WD)

2,625kg ÷ 4 × 1.2 = 788kg per wheel (AWD)

MAKSTTON recommended minimum: 739kg per wheel (2WD) and 788kg per wheel (AWD).

Load capacity should never be traded for lower wheel weight or a more aggressive wheel position. Confirm the final value against the exact vehicle version before ordering.

Measured Factory Fender Clearance

Baseline: factory 19-inch and 21-inch packages at factory suspension height, measured from the fender lip to the outer wheel rim.

Measurement Front Left Front Right Rear Left Rear Right
Fender lip to wheel rim (19-inch) ≈35mm ≈35mm ≈25mm ≈29mm
Fender lip to wheel rim (21-inch) ≈18mm ≈20mm ≈14mm ≈17mm

Use this guide as a baseline, not the final answer. Measurements from your own vehicle are always more valuable. Read our Flush Fitment Guide, measure your car, and calculate the fitment that matches the stance you want.

MAKSTTON Custom Fitment Recommendation

Based on the factory suspension height.

5mm Wheel-Rim Inset from the Fender

19-inch 8.5J

Position Wheel Size Offset Tire
Front 19×8.5J ET29 235/55R19
Rear 19×8.5J ET39 235/55R19

19-inch 8J

Position Wheel Size Offset Tire
Front 19×8J ET22 235/55R19
Rear 19×8J ET32 235/55R19

21-inch 9J

Position Wheel Size Offset Tire
Front 21×9J ET39 255/40R21
Rear 21×9J ET43 255/40R21

21-inch 8.5J

Position Wheel Size Offset Tire
Front 21×8.5J ET33 255/40R21
Rear 21×8.5J ET37 255/40R21

Fender clearance may vary slightly between vehicles due to production tolerances. Use these figures as a reference only.

Makstton Production Wheel Fitment

Size Wheel Expected Result
19-Inch 19×8.5J ET35 Tire approximately flush with the fender
21-Inch 21×9J ET35 Tire extends approximately 3mm beyond the fender

Recommended Makstton Wheel Designs

These MAKSTTON wheels are available in custom forged (FG) and flow-formed (FF) constructions, and can be produced in the recommended 19- and 21-inch LYNK & CO 08 specifications with the correct load rating, PCD and center bore for this vehicle.

Real-World Fitment 01: LYNK & CO 08

LYNK & CO 08 real-world fitment 01 on 21-inch Makstton FG FK08 forged wheels
View More Fitment Photos & Installation Details
Item Front Rear
Model MAKSTTON FG FK08
Wheel 21×8.5J ET39 21×8.5J ET39
Tire 255/40R21 255/40R21

Real-World Fitment 02: LYNK & CO 08

LYNK & CO 08 real-world fitment 02 on 21-inch Makstton FG FK07R forged wheels
View More Fitment Photos & Installation Details
Item Front Rear
Model MAKSTTON FG FK07R
Wheel 21×8.5J ET33 21×8.5J ET33
Tire 255/40R21 255/40R21

Real-World Fitment 03: LYNK & CO 08

LYNK & CO 08 real-world fitment 03 on 21-inch Makstton FF FK08 flow-formed wheels
View More Fitment Photos & Installation Details
Item Front Rear
Model MAKSTTON FF FK08
Wheel 21×9J ET35 21×9J ET35
Tire 255/40R21 255/40R21

Real-World Fitment 04: LYNK & CO 08

LYNK & CO 08 real-world fitment 04 on 21-inch Makstton FG 715 forged wheels
View More Fitment Photos & Installation Details
Item Front Rear
Model MAKSTTON FG 715
Wheel 21×8.5J ET35 21×8.5J ET35
Tire 255/40R21 255/40R21

Real-World Fitment 05: LYNK & CO 08

LYNK & CO 08 real-world fitment 05 on 19-inch Makstton FF MR7 flow-formed wheels
View More Fitment Photos & Installation Details
Item Front Rear
Model MAKSTTON FF MR7
Wheel 19×8.5J ET35 19×8.5J ET35
Tire 235/55R19 235/55R19

LYNK & CO 08 Wheel Fitment FAQ

What is the LYNK & CO 08 bolt pattern and center bore?

The LYNK & CO 08 uses a 5×108 bolt pattern with a 63.4mm published center bore (MAKSTTON machines custom wheels to 63.3mm) and an M14×1.5 wheel bolt thread. The 2WD and AWD versions share the same figures.

What wheel and tire sizes does the LYNK & CO 08 use from the factory?

The measured 2WD vehicle runs 19×7.5J ET46 wheels with 235/55R19 tires, while the AWD version runs 21×8.5J ET46 wheels with 255/40R21 tires. Both use the same size front and rear.

What wheel fitment does MAKSTTON recommend for the LYNK & CO 08?

See the final recommendation table for the current wheel-rim inset options, offsets and matching tire sizes.

What load rating does a LYNK & CO 08 wheel need?

The gross vehicle weight rating is 2,463kg for the 2WD and 2,625kg for the AWD. Applying the usual safety factor, MAKSTTON uses a minimum of 739kg per wheel (2WD) and 788kg per wheel (AWD). Load capacity should never be traded for a lower weight or a more aggressive appearance.

Should I choose 19-inch or 21-inch wheels for the LYNK & CO 08?

19-inch wheels give better daily comfort, greater tire protection and lower replacement costs. 21-inch wheels fill the wheel arch more and give a stronger visual impact. For most daily-driven vehicles MAKSTTON considers 19-inch the better overall balance, while 21-inch suits owners who put appearance first.

Do the 2WD and AWD versions of the LYNK & CO 08 use the same fitment?

They share the same 5×108 PCD, the same published 63.4mm center bore and the same M14×1.5 wheel bolt thread, and each runs the same wheel size front and rear. The factory wheel diameter differs, however — 19-inch on the 2WD and 21-inch on the AWD — so the recommended offsets are listed separately for each.

Binghua Yang, Product Development Manager, MAKSTTON

Binghua Yang | Product Development Manager

Renbing Xiong, Technical Department, MAKSTTON

Technical data: Renbing Xiong | Technical Department

If you have any questions, find an error in this guide or have additional verified fitment data, please contact MAKSTTON at info@makstton.com.