MAKSTTON VEHICLE FITMENT GUIDE

Li Auto i6 Wheel Fitment Guide

By Zhenjie Duan · November 11, 2026

This guide is based on real-world measurement data from a 2026 Li Auto i6. The test vehicle was fitted with 20×8.5J ET50.5 OE wheels, 255/50R20 tires, a 5×120 bolt pattern, and a recommended custom center bore of 62.55 mm.

This guide covers wheel installation clearance, brake calipers and hub height, wheel fasteners, valve stems, wheel load ratings, and tire fitment. It also provides suggested forged-wheel modification parameters based on measured data, together with a complete vehicle data collection record.

View fitment recommendations ↓
Li Auto i6 wheel fitment guide hero image

Li Auto i6 Fitment at a Glance

Item Data
Bolt Pattern (PCD) 5×120
Thread Specification M14×1.5
OE Nominal CB 62.5 mm
OE Wheel Size 20×8.5J ET50.5
OE Tire Size 255/50R20
GVWR 2,870 kg
Minimum Wheel Load Rating ≥ 861 kg per wheel
View vehicle body plate image
Fitment at a Glance image
Photo credit: MAKSTTON Technical Team

OE Wheel and Tire Specifications

Position OE Wheel Size OE Tire Size
Front 20×8.5J ET50.5 255/50R20
Rear 20×8.5J ET50.5 255/50R20
View OE wheel and tire photos
OE Wheel and Tire Specifications image 1
Photo credit: MAKSTTON Technical Team
OE Wheel and Tire Specifications image
Photo credit: MAKSTTON Technical Team
OE Wheel and Tire Specifications image
Photo credit: MAKSTTON Technical Team

Bolt Pattern and Center Bore

Li Auto i6 uses a 5×120 bolt pattern. The OE nominal CB is 62.5 mm; the measured wheel CB is 62.62 mm and the measured hub diameter is 62.46 mm. The recommended custom CB is 62.55 mm.

Item Data
Bolt Pattern (PCD) 5×120
OE Nominal CB 62.5 mm
Wheel CB (Measured) 62.62 mm
Measured Hub Diameter 62.46 mm
Recommended Custom CB 62.55 mm
View center bore and hub measurement photos
Bolt Pattern and Center Bore image
Photo credit: MAKSTTON Technical Team

Wheel Fastener Specifications

The fastener type for the vehicle recorded in this data-collection session is Wheel nut, with thread specification M14×1.5, thread length 30 mm, seat type 60°, strength class 10, socket size 21 mm. The new wheel's seat type, thread engagement, and socket clearance must match the OE structure; tighten to the vehicle manufacturer's specified torque.

Item Data
Fastener type Wheel nut
Thread specification M14×1.5
Thread length 30 mm
Seat type 60°
Strength class 10
Socket size 21 mm
View wheel fastener measurement photos
Wheel Fastener Specifications image 1
Photo credit: MAKSTTON Technical Team
Wheel Fastener Specifications image 2
Photo credit: MAKSTTON Technical Team
Wheel Fastener Specifications image 3
Photo credit: MAKSTTON Technical Team
Wheel Fastener Specifications image 4
Photo credit: MAKSTTON Technical Team
Wheel Fastener Specifications image 5
Photo credit: MAKSTTON Technical Team

Valve Stem and TPMS

The measured vehicle uses rubber valve stems. Before changing wheels, confirm whether the vehicle is equipped with a TPMS and verify the sensor type, mounting location, and compatibility with the wheel valve hole.

View valve stem and TPMS photos
Valve Stem and TPMS image 1
Photo credit: MAKSTTON Technical Team
Valve Stem and TPMS image 2
Photo credit: MAKSTTON Technical Team

Wheel Load Requirement

The vehicle's body plate states a maximum permissible gross mass of 2,870 kg. The original wheel is marked with a rated load of 900 kg per wheel.

Calculation Calculation Process Recommended Rated Load per Wheel
Minimum required load 2,870 kg ÷ 4 × 1.2 = 861 kg ≥ 861 kg
Forged wheel requirement 2,870 kg ÷ 4 × 1.3 = 933 kg ≥ 933 kg

Verify the maximum permissible gross mass on the vehicle identification plate. This value may differ between configurations of the same model, so calculate using the actual vehicle's plate data. The results above are for preliminary wheel-selection reference only.

Measured Wheel-to-Fender Clearance

Clearance data was measured with the 20-inch wheel and is expressed in millimeters. Assembly tolerances vary between the left and right sides. Actual clearance may change after a tire-brand change, suspension-height adjustment, or wheel alignment.

Measurement Front left Front right Rear left Rear right
Fender to wheel edge 27 mm 20 mm 26 mm 23 mm
Fender to tire sidewall 14 mm 8 mm 16 mm 12 mm
Suspension height 53 mm 60 mm 55 mm 54 mm
Fender thickness 10 mm 4 mm

This guide is a starting point, not the final answer. Measuring your own vehicle is more valuable. Read our Flush Fitment Guide, Measure Your Vehicle, and Calculate a Fitment Setup That Matches Your Target Stance.

View fender clearance measurement photos
Measured Wheel-to-Fender Clearance image 1
Photo credit: MAKSTTON Technical Team
Measured Wheel-to-Fender Clearance image 2
Photo credit: MAKSTTON Technical Team

MAKSTTON Custom Data Recommendation

Recommended custom specs aim for a full, balanced look.

Setup Tire Size Front Wheel Rear Wheel Fitment State
20-inch 255/50R20 20×8.5J ET40 20×8.5J ET40 Rim lip inset — front ~9-16 mm, rear ~12-15 mm.
21-inch 265/45R21 21×9.0J ET40 21×9.0J ET40 Rim lip inset — front ~3-10 mm, rear ~6-9 mm.

Recommended MAKSTTON Wheel Designs

Custom Forged Wheel Designs

Real-World Fitment Cases

MAKSTTON Vehicle Measurement Record

The measurement record compiles wheel size, tire specification, fender clearance, suspension clearance, center bore, and fastening hardware data for future wheel-fitment checks. For mainstream vehicles, MAKSTTON may combine measurements from multiple vehicles rather than relying on a single sheet.

MAKSTTON Vehicle Measurement Record image
Photo credit: MAKSTTON Technical Team

Frequently Asked Questions

Q:What are the bolt pattern and center bore of the Li Auto i6?

A:The bolt pattern (PCD) is 5×120. The OE nominal center bore is 62.5 mm. The measured wheel center bore is 62.62 mm. The recommended custom center bore is 62.55 mm.

Q:What are the OE wheel and tire specifications for the Li Auto i6?

A:The OE wheels are 20×8.5J, ET50.5, with 255/50R20 at both axles.

Q:What wheel sizes and offsets does MAKSTTON recommend for the Li Auto i6?

A:MAKSTTON recommends 20-inch: wheels 20×8.5J ET40, tires 255/50R20. 21-inch: wheels 21×9.0J ET40, tires 265/45R21.

Q:What wheel load rating does the Li Auto i6 require?

A:The maximum permissible gross mass is 2,870 kg. Under the current calculation rules, a conventional aftermarket wheel should be rated at no less than 861 kg per wheel, and a forged wheel at no less than 933 kg per wheel. The OE wheel is marked at 900 kg per wheel. Verify the actual gross mass on the vehicle identification plate; it may differ between configurations of the same model.

Q:What wheel bolts or nuts are used on the Li Auto i6?

A:This vehicle uses the following wheel-fastener specifications: fastener type: Wheel nut; thread specification: M14×1.5; thread length: 30 mm; seat type: 60°; strength class: 10; socket size: 21 mm.

Q:How should wheel installation clearance be verified when upgrading the brakes on the Li Auto i6?

A:Before installing an aftermarket brake caliper, request the complete caliper and mounting-bracket engineering drawings from the caliper manufacturer. MAKSTTON provides measurement drawings for the OE braking system that can help verify the custom bracket dimensions and installation position. Final fitment must still be confirmed against the caliper shape, the wheel's internal structure, and actual installation clearance.

段振杰, Zhenjie Duan, 技术部门, Technical Department, MAKSTTON

Author:Zhenjie Duan | Technical Department

熊仁兵, Renbing Xiong, 技术部门, Technical Department, MAKSTTON

Data:Renbing Xiong | Technical Department

If you have questions, find an error, or have verified supplementary fitment data, contact MAKSTTON: info@makstton.com.